Kraken Gearbox jam

Deaf_shooter · December 27th, 2009, 00:42

My brother open up gearbox and replace one stuff(I haven't ask what is name of thing he replace. It look like tube that attach to one end of spring) then put all together under direction of youtube (not whole, just 2 gear left that has do with semi and auto selector). when he test it, he manage to get one shot before it jam. Motor still run but gear won't move, my brother and I try to move but it is stuck.

Slow · December 27th, 2009, 01:44

What type of gearbox and turn the hopup down

RaisinBran · December 27th, 2009, 01:50

Quote:

Originally Posted by Deaf_shooter

My brother open up gearbox and replace one stuff(I haven't ask what is name of thing he replace. It look like tube that attach to one end of spring) then put all together under direction of youtube (not whole, just 2 gear left that has do with semi and auto selector). when he test it, he manage to get one shot before it jam. Motor still run but gear won't move, my brother and I try to move but it is stuck.

Check the battery...

Deaf_shooter · December 27th, 2009, 02:17

I don't think battery is issue but I will check anyway

Deaf_shooter · December 27th, 2009, 02:34

kk, first battery which my brother test is 8.1 volt, second one is 8.7 volt, one I test, after move white plastic that look like that has do with semi-auto selector. it work... but I will test it futher.

still jam sometime

and I think it is V3, but I am not sure

Doc · December 27th, 2009, 06:25

its a v3 gearbox, there is a little hex screw at the bottom of the motor, try turning it right one or 2 turns, and see if that works.

CRichards · December 27th, 2009, 15:58

Hey i'm deaf_shooter's brother, i replaced the nylon bushings with metal ones, i added a bearing spring guide and a new piston head. When i put it back together, i put a fully charged battery on it, it cranked once, went bang :P (louder than i remember it banging before) then it wouldn't shoot again. The motor still works when i pull the trigger, you can hear it struggleing when the trigger is pulled, when i took the motor off the mechbox but left the electrical connected, it spins when the trigger is pulled. the gears inside turn kinda but they're real hard to move (i'd assume cause they're pushing a spring). One thing i did notice though is that with the new metal bushings, they seemed to go through the mechbox housing a little further than the old nylon ones. not a huge issue but one of the bushings kind of pushes on a plastic piece on the outside of the mechbox. my brother pointed out that when he moves that piece the gun seems to fire.... kinda weird. any suggestions?

Amos · December 27th, 2009, 16:03

Your shimming is off, by the sounds of it everything is shimmed way too tight.

You may also need a "selector" switch that can accommodate normal sized bushings.

lemegacool · December 27th, 2009, 16:04

edit ^^ damnit lol

did you re-did a proper shim job? a shim job is mandatory with new bushing...

CRichards · December 27th, 2009, 17:07

i put the gears in and shimmed them before adding anything else back into the mechbox, closed it and spun the gears. they spun fine so i figured i was good to go. i didn't put the screws in to hold the mechbox together though when i tested it. maybe i'll try re-shimming and see if that solves the problem. here's to hoping :P

lemegacool · December 27th, 2009, 18:01

Quote:

Originally Posted by CRichards

i put the gears in and shimmed them before adding anything else back into the mechbox, closed it and spun the gears. they spun fine so i figured i was good to go. i didn't put the screws in to hold the mechbox together though when i tested it. maybe i'll try re-shimming and see if that solves the problem. here's to hoping :P

yep when shimming you have to put the screws back after each try to properly set the shimming... that is what makes shimming LONG.... personally i dont put ALL the screws back... only 3 around the gear "casing" and remember to shim each gear one by one, meaning that you put the spur gear, shim it then add sector gear and shim it and finish with the bevel gear

Amos · December 27th, 2009, 18:16

Once everything was put in, how many revolutions of "Free spin" did you get out of the sector gear?

Deaf_shooter · December 29th, 2009, 19:54

I reopen and shim everything. I double check to make sure both side has shim, then spin them with hand one gear by one. After I do get all gear inside. I attach motor and apply grease to gear. Plus I also do put bearing oil to where bearing is. Then I hold trigger in auto, until grease spread even on gears. After this, I put everything in again. I test once agan and same problem appear again. I try other battery because first one is weakened from free span for grease reason. same problem remain. It still have hard time. then I grab my Kraken's fresh charge from overnight. it now work like charm.

It make me think if Battery was issue in first place.

Edit: try to improved my grammar

SHÖCK · December 30th, 2009, 11:07

Do you know how to shim properly? Was the gearbox definetely screwed together?

If that is fine then I am pretty sure it's your battery. It's getting old/damaged and doesn't have enough power to turn over your motor since the spring in the Kraken is good for 400 FPS.

Deaf_shooter · December 30th, 2009, 12:53

ya, gearbox is screwed together. while I don't know well about shim. I follow description from brother. but like I said it work fine now

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

December 27th, 2009, 00:42	#1
Deaf_shooter Trader rating Join Date: Feb 2009 Location: Winnipeg, Manitoba	Kraken Gearbox jam My brother open up gearbox and replace one stuff(I haven't ask what is name of thing he replace. It look like tube that attach to one end of spring) then put all together under direction of youtube (not whole, just 2 gear left that has do with semi and auto selector). when he test it, he manage to get one shot before it jam. Motor still run but gear won't move, my brother and I try to move but it is stuck. __________________ my english is bad. however, It don't make up different on your ignorance.

December 27th, 2009, 01:44	#2
Slow Loves Furries Trader rating Join Date: Oct 2009 Location: Manitoba	What type of gearbox and turn the hopup down __________________ If ASC were real life, there would be no Chuck Norris, only CDN_Stalker MANITOBA IVAN

December 27th, 2009, 02:17	#4
Deaf_shooter Trader rating Join Date: Feb 2009 Location: Winnipeg, Manitoba	I don't think battery is issue but I will check anyway __________________ my english is bad. however, It don't make up different on your ignorance.

December 27th, 2009, 02:34	#5
Deaf_shooter Trader rating Join Date: Feb 2009 Location: Winnipeg, Manitoba	kk, first battery which my brother test is 8.1 volt, second one is 8.7 volt, one I test, after move white plastic that look like that has do with semi-auto selector. it work... but I will test it futher. still jam sometime and I think it is V3, but I am not sure __________________ my english is bad. however, It don't make up different on your ignorance. Last edited by Deaf_shooter; December 27th, 2009 at 04:04..

December 27th, 2009, 06:25	#6
Doc Trader rating Join Date: Apr 2006 Location: Toronto	its a v3 gearbox, there is a little hex screw at the bottom of the motor, try turning it right one or 2 turns, and see if that works. __________________ Guardians of Asgaard

December 27th, 2009, 15:58	#7
CRichards Trader rating Join Date: Nov 2008	Hey i'm deaf_shooter's brother, i replaced the nylon bushings with metal ones, i added a bearing spring guide and a new piston head. When i put it back together, i put a fully charged battery on it, it cranked once, went bang :P (louder than i remember it banging before) then it wouldn't shoot again. The motor still works when i pull the trigger, you can hear it struggleing when the trigger is pulled, when i took the motor off the mechbox but left the electrical connected, it spins when the trigger is pulled. the gears inside turn kinda but they're real hard to move (i'd assume cause they're pushing a spring). One thing i did notice though is that with the new metal bushings, they seemed to go through the mechbox housing a little further than the old nylon ones. not a huge issue but one of the bushings kind of pushes on a plastic piece on the outside of the mechbox. my brother pointed out that when he moves that piece the gun seems to fire.... kinda weird. any suggestions?

December 27th, 2009, 16:03	#8
Amos Trader rating Join Date: Aug 2006 Location: Japan	Your shimming is off, by the sounds of it everything is shimmed way too tight. You may also need a "selector" switch that can accommodate normal sized bushings. __________________ Custom Builds: FA3674U Krinkov G3SD6 Last edited by Amos; December 27th, 2009 at 16:06..

December 27th, 2009, 16:04	#9
lemegacool Trader rating Join Date: Aug 2008 Location: notre dame des prairies /quebec	edit ^^ damnit lol did you re-did a proper shim job? a shim job is mandatory with new bushing... __________________ member of fire team NOM. my other regular forum: www.toyotanation.com / gen3,gen4 camry

December 27th, 2009, 17:07	#10
CRichards Trader rating Join Date: Nov 2008	i put the gears in and shimmed them before adding anything else back into the mechbox, closed it and spun the gears. they spun fine so i figured i was good to go. i didn't put the screws in to hold the mechbox together though when i tested it. maybe i'll try re-shimming and see if that solves the problem. here's to hoping :P

December 27th, 2009, 18:16	#12
Amos Trader rating Join Date: Aug 2006 Location: Japan	Once everything was put in, how many revolutions of "Free spin" did you get out of the sector gear? __________________ Custom Builds: FA3674U Krinkov G3SD6

December 29th, 2009, 19:54	#13
Deaf_shooter Trader rating Join Date: Feb 2009 Location: Winnipeg, Manitoba	I reopen and shim everything. I double check to make sure both side has shim, then spin them with hand one gear by one. After I do get all gear inside. I attach motor and apply grease to gear. Plus I also do put bearing oil to where bearing is. Then I hold trigger in auto, until grease spread even on gears. After this, I put everything in again. I test once agan and same problem appear again. I try other battery because first one is weakened from free span for grease reason. same problem remain. It still have hard time. then I grab my Kraken's fresh charge from overnight. it now work like charm. It make me think if Battery was issue in first place. Edit: try to improved my grammar __________________ my english is bad. however, It don't make up different on your ignorance. Last edited by Deaf_shooter; December 29th, 2009 at 20:03..

December 30th, 2009, 11:07	#14
SHÖCK aka SNK or Shaniqua Trader rating Join Date: May 2008 Location: Calgary, AB	Do you know how to shim properly? Was the gearbox definetely screwed together? If that is fine then I am pretty sure it's your battery. It's getting old/damaged and doesn't have enough power to turn over your motor since the spring in the Kraken is good for 400 FPS. __________________ SHÖCK Last edited by SHÖCK; December 30th, 2009 at 11:10..

December 30th, 2009, 12:53	#15
Deaf_shooter Trader rating Join Date: Feb 2009 Location: Winnipeg, Manitoba	ya, gearbox is screwed together. while I don't know well about shim. I follow description from brother. but like I said it work fine now __________________ my english is bad. however, It don't make up different on your ignorance.

Kraken Gearbox jam

Doctor's Corner