G&G GR-16 BB Plastica version Problem?

Boomshakah · August 16th, 2009, 15:30

My GR 16 blowback have some kind of problem, the front end is not fixed to the gun, if i pull it a little bit, it comes off and shows the inner barrell, and i don't know how to fix this. miss a screw? need some glue? any idea how to fix this? well thanks in advance for the help

Shaun655 · August 21st, 2009, 18:38

Hi, I own the GR16 A3 with full stock. The part you are talking about if its the hand-guard then no its not held on with any screws. You can remove the top and bottom hand-guard on mine to reveal the outer barrel. For me though this is not something that easily comes apart. You have to pull back on the ring close to the body of the gun itself and while doing that try to pop out the hand-guard which I often use a screw driver to make happen. When you put the parts back together try to make sure they are seated properly near the front sight then lower the rear part of the hand guard into place and make sure the ring that secures them is back in place. If you want a visual walk through G&G has pictures in there manual I believe, plus they have videos on how to take apart you G&G on the net.

Boomshakah · August 22nd, 2009, 22:30

Thanks, but i've fixed my problem, there was a missing screw where the barrel is held to the body of the gun.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 16th, 2009, 15:30	#1
Boomshakah Trader rating Join Date: May 2009 Location: Trois Rivières, Québec	G&G GR-16 BB Plastica version Problem? My GR 16 blowback have some kind of problem, the front end is not fixed to the gun, if i pull it a little bit, it comes off and shows the inner barrell, and i don't know how to fix this. miss a screw? need some glue? any idea how to fix this? well thanks in advance for the help Last edited by Boomshakah; August 19th, 2009 at 17:24..

August 21st, 2009, 18:38	#2
Shaun655 Trader rating Join Date: Apr 2007 Location: Wasaga Beach	Hi, I own the GR16 A3 with full stock. The part you are talking about if its the hand-guard then no its not held on with any screws. You can remove the top and bottom hand-guard on mine to reveal the outer barrel. For me though this is not something that easily comes apart. You have to pull back on the ring close to the body of the gun itself and while doing that try to pop out the hand-guard which I often use a screw driver to make happen. When you put the parts back together try to make sure they are seated properly near the front sight then lower the rear part of the hand guard into place and make sure the ring that secures them is back in place. If you want a visual walk through G&G has pictures in there manual I believe, plus they have videos on how to take apart you G&G on the net.

August 22nd, 2009, 22:30	#3
Boomshakah Trader rating Join Date: May 2009 Location: Trois Rivières, Québec	Thanks, but i've fixed my problem, there was a missing screw where the barrel is held to the body of the gun.

G&G GR-16 BB Plastica version Problem?

Doctor's Corner