Airsoft Canada
https://www.replicaairguns.ca/airsoft

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

G36 massive low FPS

:

Doctor's Corner

Reply
 
Thread Tools
Old February 26th, 2008, 13:07   #1
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
G36 massive low FPS

Well, my G36 is shooting around 240 Fps... it has an MS100SP spring, so I figure it should be shooting at least 320. The spring and spring guides are the only upgrades to this gun.

Things I have checked:
-Piston Seal: I thought I was getting bad compression, so I replaced the O-ring. FPS went up from 220 to 240. Getting good compression now so I don't think that's it.
-Hop-up: Hop-up is off, assembled and seated correctly.

Things I suspect:
-Spring: I'm guessing maybe I have a bum spring. I can swap it with the stock one or I may just put in a 110 or 120.

Things I don't know:
-Wondering if there is anythign else I should check next time I have the mechbox apart that could be causing the FPS loss?
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
Old February 26th, 2008, 13:28   #2
tomsoderman
 
Join Date: Feb 2005
busted cylinder head maybe
tomsoderman is offline   Reply With Quote
Old February 26th, 2008, 13:39   #3
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
Cylinder head seems fine (didn't see any cracks), and I'm getting a great seal between it and the cylinder. (I can put my finger over the nozzel and I can barley push the piston in).
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
Old February 26th, 2008, 14:25   #4
Dr.
 
Dr.'s Avatar
 
Join Date: May 2007
Location: Victoria, B.C.
Is it the G36c or the full length?

If it's the "C", did you put your cylinder in with the side vent window towards the back or front of the mechbox? (should be back)

also, if it's a non-linear spring, make sure your tighter coils are towards the back end of the gun as well.

I know these might seem like noobish mistakes but I made the first one when I first upgraded my gun.

Good luck in solving your problem.
__________________
"I'm not a real Doctor, I just play one on the Internet"

Dr. is offline   Reply With Quote
Old February 26th, 2008, 14:28   #5
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
Quote:
Originally Posted by Dr. View Post
Is it the G36c or the full length?

If it's the "C", did you put your cylinder in with the side vent window towards the back or front of the mechbox? (should be back)
Naw, CA36E

Quote:
also, if it's a non-linear spring, make sure your tighter coils are towards the back end of the gun as well.
I considered that one as well, but the spring is installed correctly.

Quote:
I know these might seem like noobish mistakes but I made the first one when I first upgraded my gun.
That's how we learn

Quote:
Good luck in solving your problem.
Thanks
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
Old February 26th, 2008, 15:55   #6
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
does it have a ventilated piston head or not?
__________________
Jimski is offline   Reply With Quote
Old February 26th, 2008, 16:11   #7
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
Quote:
Originally Posted by Jimski View Post
does it have a ventilated piston head or not?
Yes the piston head is vented.
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
Old February 26th, 2008, 16:21   #8
Glock 18
 
Glock 18's Avatar
 
Join Date: Sep 2004
Location: Bradford, ONT
Send a message via MSN to Glock 18
could just be a lemon spring, i ordered a PDI 120% spring once and it was so fucking strong that a huge 12V couldn,t even compress it.
__________________
--------------------------------------------------
Glock 18 is offline   Reply With Quote
Old February 26th, 2008, 16:24   #9
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
Quote:
Originally Posted by Glock 18 View Post
could just be a lemon spring, i ordered a PDI 120% spring once and it was so fucking strong that a huge 12V couldn,t even compress it.
That's the direction I'm leaning too. The spring was one of the first upgrades I did to this gun, and it seems that since then it's performance has been inconsistent at best -I always chocked it up to something else but I'm quickly running out of options.
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
Old February 26th, 2008, 17:21   #10
specter_M4
 
specter_M4's Avatar
 
Join Date: Feb 2002
Location: Calgary, Alberta
Send a message via AIM to specter_M4 Send a message via MSN to specter_M4 Send a message via Skype™ to specter_M4
It must be the spring. If you've checked everything properly and your getting good compression...
__________________



specter_M4 is offline   Reply With Quote
Old February 26th, 2008, 17:36   #11
Spa
 
Spa's Avatar
 
Join Date: Oct 2006
Location: Winnipeg, Manitoba
have u tried putting your other spring back in to conclude u have a lemon spring?
Spa is offline   Reply With Quote
Old February 26th, 2008, 17:46   #12
Visser
 
Visser's Avatar
 
Join Date: Oct 2004
Location: Cocagne, NB
Send a message via MSN to Visser
I have the same problem w/ a buddy's G36E and I had a guarder 150 spring around and just to see what it would do we put it in knowing it should shoot really hard but it only shot 385-398 fps. We checked EVERYTHING in there and can't figure out why its doing that. He has a bore up kit in there as well thinkin that it should help push it more...we're stumped on where the air loss is???
Visser is offline   Reply With Quote
Old February 26th, 2008, 17:55   #13
happytit
 
happytit's Avatar
 
Join Date: May 2006
Location: Montreal
Send a message via MSN to happytit
Quote:
Originally Posted by Spa View Post
have u tried putting your other spring back in to conclude u have a lemon spring?
that might be it

it might also be the hopup is not makeing a good seal around the barrel and the air might be getting out there.

you might want to try a full metal hopup assembly insted of the stock plasitc ones.

even thogh you have conf that it looks fine sometimes air can find places to go that the eye can't see

that might be the place that you are loseing the FPS
__________________

[MTX]HappyTiT Recon rifleman
Primary Weapons // G36c, HK416
Secondary Weapons // Glock 18C

Last edited by happytit; February 26th, 2008 at 17:58..
happytit is offline   Reply With Quote
Old February 26th, 2008, 19:03   #14
The Saint
 
The Saint's Avatar
 
Join Date: Jan 2005
Location: Quebec
Quote:
Originally Posted by Visser View Post
He has a bore up kit in there as well thinkin that it should help push it more...
Take the bore up kit OUT unless he's got a barrel around 700mm or longer. Bore up kits are not "upgrades" per say, they're really only useful in guns with ridiculously long barrels. In a normal AEG like a G36, all it's going to do is reduce your potential fps.
__________________
"The Bird of Hermes is My Name, Eating My Wings to Make Me Tame."
The Saint is offline   Reply With Quote
Old February 26th, 2008, 19:50   #15
kalnaren
 
kalnaren's Avatar
 
Join Date: Dec 2006
Location: Midland, Ontario
Quote:
Originally Posted by happytit View Post
that might be it

it might also be the hopup is not makeing a good seal around the barrel and the air might be getting out there.

you might want to try a full metal hopup assembly insted of the stock plasitc ones.

even thogh you have conf that it looks fine sometimes air can find places to go that the eye can't see

that might be the place that you are loseing the FPS
I'll check that too. It and the spring are about the only things I can think of.
__________________

Quote:
"Someone in a Prius tried to race me at a stop sign the other day. I couldn't believe it. I had him for the first 100 feet or so but I can only walk so fast."
kalnaren is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
https://www.replicaairguns.ca/airsoft

All times are GMT -4. The time now is 20:55.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.