D Boy gear

Saint_blackhand · May 30th, 2007, 22:33

Does anyone use these chinese knock offs, they are a good price and they look good. Does anyone know anything about them good/ bad? I am looking at the ACE stock and a mag well thing.

zone 69 · December 14th, 2007, 01:28

There OK i got three D-boys m4 mags two 300rd high caps & a 190rd vn mid. There a little ruff looking but not to bad and they work fine. But im having problums with the vn fitting in the mag well it,s to sloppy so it gives me a feeding prob. But i think some tape will fix the slop. your getting what you pay for i gess. hope this help,s. I think this thread is in the wrong sec.

Killbucket · December 18th, 2007, 12:54

I have MANY D-Boys rifles. To make a mag work, slightly trim the release tab at the top. D-Boys rifles Hop up feed tubes don't push this part back far enough to let the BB's out of the magazine.
Trust me on this, I tried everything at first, and this is what works. Just use an xacto knife to trim a little off the pointed end of the catch, and try it till it works.
As you can tell, it won't take much. Just pushing the mags up makes them work, so it's a tiny change that's needed.
Notice the D-Boys SPR in this vid has no problem shooting from the Marui magazine that's in it:
http://www.youtube.com/watch?v=58vIxWIkx8o
This gun is a tank! Check out how the heft of it hits my left hand...

huang · December 18th, 2007, 13:06

ACE stock and a mag well are not from DBoy, but from SP.

DuffMan · December 18th, 2007, 13:12

The ACE stock is a pretty good product. My gunsmith had to file it a bit to get some wiring to fit, and it doesn't exactly fit the Lipo batteries as advertised. I would get the nicd custom substitute. The build quality is pretty good though.

shadow_matter · December 18th, 2007, 19:50

A buddy of mine just received a 416 grip from that company. The build quality is fine (ABS plastic is ABS plastic, for this application the marginal difference in quality is irrelevant) the exterior finish was nicely done, but one of the mounting screw holes was slightly mis-aligned. It was close enough that when he drove the screw in it seated itself in the grip properly. I mean, for $15 how can you go wrong?

caboose36 · December 18th, 2007, 20:50

Hey all! I puchused a M4 grip, a spare motor, and delta ring made by Dboys. Its ok quality but the paint finish on the delta ring assembly could of been a little better. But i mean for the price you couldent of gone wrong!

www.rsov.com --- go there!

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 30th, 2007, 22:33	#1
Saint_blackhand Trader rating Join Date: Mar 2007 Location: Maple Ridge BC Canada	D Boy gear Does anyone use these chinese knock offs, they are a good price and they look good. Does anyone know anything about them good/ bad? I am looking at the ACE stock and a mag well thing. __________________ I enjoy facebook stalking all of you! I shop here : www.Pocomilitary.com www.halifaxairsoftwholesale.com

December 14th, 2007, 01:28	#2
zone 69 Trader rating Join Date: Sep 2006 Location: KELOWNA , B.C CANADA, PLANET EARTH	There OK i got three D-boys m4 mags two 300rd high caps & a 190rd vn mid. There a little ruff looking but not to bad and they work fine. But im having problums with the vn fitting in the mag well it,s to sloppy so it gives me a feeding prob. But i think some tape will fix the slop. your getting what you pay for i gess. hope this help,s. I think this thread is in the wrong sec. Last edited by zone 69; December 14th, 2007 at 19:24..

December 18th, 2007, 13:12	#5
DuffMan Trader rating Join Date: Feb 2004	The ACE stock is a pretty good product. My gunsmith had to file it a bit to get some wiring to fit, and it doesn't exactly fit the Lipo batteries as advertised. I would get the nicd custom substitute. The build quality is pretty good though. __________________ "He resisted. I asked him to comply." "Telling him to 'eat it, bitch' is not really a request."

December 18th, 2007, 12:54	#3
Killbucket Trader rating Join Date: Jan 2007 Location: Citrus Heights, CA	I have MANY D-Boys rifles. To make a mag work, slightly trim the release tab at the top. D-Boys rifles Hop up feed tubes don't push this part back far enough to let the BB's out of the magazine. Trust me on this, I tried everything at first, and this is what works. Just use an xacto knife to trim a little off the pointed end of the catch, and try it till it works. As you can tell, it won't take much. Just pushing the mags up makes them work, so it's a tiny change that's needed. Notice the D-Boys SPR in this vid has no problem shooting from the Marui magazine that's in it: http://www.youtube.com/watch?v=58vIxWIkx8o This gun is a tank! Check out how the heft of it hits my left hand...

December 18th, 2007, 13:06	#4
huang Trader rating Join Date: Dec 2001 Location: Scarborough	ACE stock and a mag well are not from DBoy, but from SP.

December 18th, 2007, 19:50	#6
shadow_matter Trader rating Join Date: Dec 2006 Location: Kitchener Ontario	A buddy of mine just received a 416 grip from that company. The build quality is fine (ABS plastic is ABS plastic, for this application the marginal difference in quality is irrelevant) the exterior finish was nicely done, but one of the mounting screw holes was slightly mis-aligned. It was close enough that when he drove the screw in it seated itself in the grip properly. I mean, for $15 how can you go wrong? __________________ Call sign: Shadow_Matter "I play airsoft, yes yes..."

December 18th, 2007, 20:50	#7
caboose36 Trader rating Join Date: Nov 2007 Location: Winnipeg, Manitoba	Hey all! I puchused a M4 grip, a spare motor, and delta ring made by Dboys. Its ok quality but the paint finish on the delta ring assembly could of been a little better. But i mean for the price you couldent of gone wrong! www.rsov.com --- go there!

D Boy gear

Upgrades & Modifications