CA CA4 KM 12 mosfet battery issue

kharyunn · October 29th, 2016, 17:16

Hello I have one of the new CA CA4 KM 12 mosfet and I have tried to run it on a 7.4 lipo and it will not run at all. I changed to a 11.1 lipo and it worked fine. I also used a 9.6 nicad and that worked for 10 shots. What could be the issue that I am having. PS the 11.1 will not fit in the buffer tube due to where the mosfet is.

Thanks
Kharyunn

Styrak · November 1st, 2016, 02:39

Are all your batteries fully charged? Is this a brand new gun? Has anything been done to it?

kharyunn · November 1st, 2016, 21:10

Brand new gun. All battles fully charged only works on an 11.1. tried about 15 different batteries

RainyEyes · November 1st, 2016, 21:53

Sounds like a wire is being pinched or there's a loose wire. From what you describe it sounds like the placement of the battery inside the buffer tube might be messing something up but when it is outside the problem does not occur?

Inspect the line please or disassemble the externals so that you only have the gearbox and a connected motor.

I had an aeg's solder connector fall off its contacts with the trigger when I was changing a spring once. QC at its finest.

ccyg8774 · November 2nd, 2016, 17:42

Get a multimeter
Measure the voltage cross the motor leads (with motor disconnected)
I would recommend doing this whenever suspecting a problem in the circuit, expecally when a MOSFET is involved.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

October 29th, 2016, 17:16	#1
kharyunn Trader rating Join Date: Mar 2010 Location: Barrie, On	CA CA4 KM 12 mosfet battery issue Hello I have one of the new CA CA4 KM 12 mosfet and I have tried to run it on a 7.4 lipo and it will not run at all. I changed to a 11.1 lipo and it worked fine. I also used a 9.6 nicad and that worked for 10 shots. What could be the issue that I am having. PS the 11.1 will not fit in the buffer tube due to where the mosfet is. Thanks Kharyunn

November 1st, 2016, 02:39	#2
Styrak Trader rating Join Date: Jan 2007 Location: Saskatoon, SK	Are all your batteries fully charged? Is this a brand new gun? Has anything been done to it? __________________ Airsoft Sales and Repair/Upgrade Services

November 1st, 2016, 21:53	#4
RainyEyes Trader rating Join Date: Sep 2013 Location: Scarbororororough	Sounds like a wire is being pinched or there's a loose wire. From what you describe it sounds like the placement of the battery inside the buffer tube might be messing something up but when it is outside the problem does not occur? Inspect the line please or disassemble the externals so that you only have the gearbox and a connected motor. I had an aeg's solder connector fall off its contacts with the trigger when I was changing a spring once. QC at its finest. Last edited by RainyEyes; November 1st, 2016 at 21:57..

November 1st, 2016, 21:10	#3
kharyunn Trader rating Join Date: Mar 2010 Location: Barrie, On	Brand new gun. All battles fully charged only works on an 11.1. tried about 15 different batteries

November 2nd, 2016, 17:42	#5
ccyg8774 Trader rating Join Date: Jun 2012 Location: Brampton, ON	Get a multimeter Measure the voltage cross the motor leads (with motor disconnected) I would recommend doing this whenever suspecting a problem in the circuit, expecally when a MOSFET is involved. __________________

CA CA4 KM 12 mosfet battery issue

Doctor's Corner