WETTI/AWSS - M4/SCAR/HK416 - Technical Summary Thread

Eeyore · January 12th, 2011, 21:52

Ok thats good. Thanks

But is the long part of the sear spring suppose to go towards the front of the receiver or the stock?

Ross · January 13th, 2011, 03:04

New question! Does a longer inner barrel do anything for the we scar accuracy or range wise?
And I see the triggers are prone to breaking. I bought a trigger assembly kit from ra-tech and put in the all the cnc'd pieces that came with it. Except the trigger. I noticed the trigger they sent me was smaller. I thought maybe it's the one for the m4. I put it in and the trigger locks up when firing on semi or full. Assuming the trigger was the problem, I put the stock one back in. No problems now, just waiting for the white metal trigger to snap.

Eeyore · January 13th, 2011, 18:19

Ok so I installed a steel part #66 and 61 from Ra-tech, now my gun only fires in full auot and as soon as I put a mag in it starts to leak gas from the mag. Any hints on where to start trouble shooting?

onemenace · January 13th, 2011, 19:18

Quote:

Originally Posted by Eeyore

Ok so I installed a steel part #66 and 61 from Ra-tech, now my gun only fires in full auot and as soon as I put a mag in it starts to leak gas from the mag. Any hints on where to start trouble shooting?

you sure you put in the metal pin for the selector switch properly? I was just giving my m4 a through cleanout yesterday and forgot that piece out and was racking my brain why the selector switch was so loose only after seeing it an hour later did it sync in ;( lol

Eeyore · January 13th, 2011, 19:28

Quote:

Originally Posted by onemenace

you sure you put in the metal pin for the selector switch properly? I was just giving my m4 a through cleanout yesterday and forgot that piece out and was racking my brain why the selector switch was so loose only after seeing it an hour later did it sync in ;( lol

How would I know if it was in improperly?

MilanWG · January 13th, 2011, 19:30

Quick question to all you WE M4 users:

Any experience with the WE M4 C02 mags?

I have heard they leak right away and they are a pain in the ass.

I would love to have a mag that works in cold-weather - but don't want something that is going to work half the time...

onemenace · January 13th, 2011, 19:46

I finally tried to shave down the diameter on my stock nozzle and previous to this it was getting stuck making it pretty hard to remove.

Now I have went over it with 600 grit wet/dry sandpaper and now its much much smoother when it gets stuck it requires a quarter of the energy of what it used to, to remove but I am still jamming bb's.

I'm not sure how much more I want to take it down because anymore and it might be too loose.

I could really use some advice on this and I'm not sure how to proceed but I cant give up on getting this thing working.

Currently I',m using the light green hopup that almost looks like a V instead of the dark black hopup (I've seen it pictures they were using it and it thought might help due to the tightness of thew new barrel)

I really hope someone can shed successful ra tech inner barrel light on the closed bolt system so we can end this fiasco!

AngelusNex · January 13th, 2011, 20:08

Quote:

Originally Posted by TALIBANMILAN

Quick question to all you WE M4 users:

Any experience with the WE M4 C02 mags?

I have heard they leak right away and they are a pain in the ass.

I would love to have a mag that works in cold-weather - but don't want something that is going to work half the time...

Got 4 for my WE scar, 2 leaked out of the box but once i put some silly oil on them and tightened them up the leaks mostly stopped (one still has a small leak but it stops after approx. 1-2 shot worth of gas leak out)

And they work wicked in -5 weather, have yet to test them in any colder yet though.

onemenace · January 13th, 2011, 20:09

Quote:

Originally Posted by AngelusNex

Got 4 for my WE scar, 2 leaked out of the box but once i put some silly oil on them and tightened them up the leaks mostly stopped (one still has a small leak but it stops after approx. 1-2 shot worth of gas leak out)

And the work wicked in -5 weather, have yet to test them in any colder yet though.

wow really -5 hot diggity dam im getting some c02 mags!

AngelusNex · January 13th, 2011, 20:23

Quote:

Originally Posted by onemenace

wow really -5 hot diggity dam im getting some c02 mags!

have yet to game it in that temp but i went out to my parents place in the country and left the gun and some fully loaded mags in my truck outside for about 5 hours before testing it, got the full 30 rounds out though the last 2-3 were lower power. All in all very impressive.

MilanWG · January 13th, 2011, 20:31

Have you experienced any malfunctions or jams as result of the higher pressure from the C02 compared with propane?

I remember I tested a M4 C02 mag and it jammed in my rifle...

AngelusNex · January 13th, 2011, 20:57

Quote:

Originally Posted by TALIBANMILAN

Have you experienced any malfunctions or jams as result of the higher pressure from the C02 compared with propane?

I remember I tested a M4 C02 mag and it jammed in my rifle...

I've had one issue while using the co2 in my scar and that was the hammer falling out of alignment but it was mostly a wear issue as the hammer is one of the few non reinforced steal parts in my gun just cause the valve knocker to not reset (needed to disassemble and manually push it down to reset)

Now i must add though, I'm going to be getting a full loadout of propane mags for her to use in the summer to minimize gun damage as co2 is unnecessary(and costs more to run) in the warm.

spartan117 · January 15th, 2011, 05:31

Quote:

Originally Posted by Mr.Hitman

Yes, mine is Huangs..
Installing the original delta ring with the DD rail? That wouldn't fit...

i never said with the DD rail. I said to try to install the original delta ring to see if there is any wobble. If there isn't then the clone mk18 rail delta is the problem. As i have said before.... switching to a socom gear mk18 rail fixed my problem.

Ross · January 15th, 2011, 22:06

Quote:

Originally Posted by onemenace

Now I have went over it with 600 grit wet/dry sandpaper and now its much much smoother when it gets stuck it requires a quarter of the energy of what it used to, to remove but I am still jamming bb's.

when it "gets stuck" is it your valve getting stuck in the black rubber nub piece?

Ballcancer · January 15th, 2011, 22:38

Hey, Angelusnex my propane mags destroyed my hammer to probably not as quickly or as severly as the CO2 mags but I have to replace it non the less.

Considering how much abuse these guns take, they are built fairly well.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 13th, 2011, 03:04	#587
Ross Trader rating Join Date: Nov 2009 Location: Winnipeg	New question! Does a longer inner barrel do anything for the we scar accuracy or range wise? And I see the triggers are prone to breaking. I bought a trigger assembly kit from ra-tech and put in the all the cnc'd pieces that came with it. Except the trigger. I noticed the trigger they sent me was smaller. I thought maybe it's the one for the m4. I put it in and the trigger locks up when firing on semi or full. Assuming the trigger was the problem, I put the stock one back in. No problems now, just waiting for the white metal trigger to snap. Last edited by Ross; January 13th, 2011 at 03:08..

January 13th, 2011, 19:30	#591
MilanWG Perroz Designs Trader rating Join Date: Jul 2003 Location: Toronto, ON	Quick question to all you WE M4 users: Any experience with the WE M4 C02 mags? I have heard they leak right away and they are a pain in the ass. I would love to have a mag that works in cold-weather - but don't want something that is going to work half the time... __________________

January 13th, 2011, 20:31	#596
MilanWG Perroz Designs Trader rating Join Date: Jul 2003 Location: Toronto, ON	Have you experienced any malfunctions or jams as result of the higher pressure from the C02 compared with propane? I remember I tested a M4 C02 mag and it jammed in my rifle... __________________

January 13th, 2011, 19:46	#592
onemenace Banned Trader rating Join Date: Oct 2008 Location: oakville	I finally tried to shave down the diameter on my stock nozzle and previous to this it was getting stuck making it pretty hard to remove. Now I have went over it with 600 grit wet/dry sandpaper and now its much much smoother when it gets stuck it requires a quarter of the energy of what it used to, to remove but I am still jamming bb's. I'm not sure how much more I want to take it down because anymore and it might be too loose. I could really use some advice on this and I'm not sure how to proceed but I cant give up on getting this thing working. Currently I',m using the light green hopup that almost looks like a V instead of the dark black hopup (I've seen it pictures they were using it and it thought might help due to the tightness of thew new barrel) I really hope someone can shed successful ra tech inner barrel light on the closed bolt system so we can end this fiasco!

January 15th, 2011, 22:38	#600
Ballcancer Trader rating Join Date: Oct 2009 Location: Gravenhurst, ON	Hey, Angelusnex my propane mags destroyed my hammer to probably not as quickly or as severly as the CO2 mags but I have to replace it non the less. Considering how much abuse these guns take, they are built fairly well. __________________

WETTI/AWSS - M4/SCAR/HK416 - Technical Summary Thread

Upgrades & Modifications