WETTI/AWSS - M4/SCAR/HK416 - Technical Summary Thread

Shirley · May 13th, 2010, 03:37

Quote:

Originally Posted by Daviday

OK I need a hand.

I installed the TSC Hammer, spring, and Disconnect. The gun shoot but it jams/the trigger lock will not disengage, unless i push the trigger forward a little then pull it again and it shoots.

Can anyone explain how to fix this?

What do you mean by spring and disconnect? What aftermarket parts are those, and spring for what?

Reading your sig that you have a WE SCAR, is yours a clear version?
Also, when pulling the trigger, were you in semi, or full auto?

Did you try it with your lower off and then put it back on to test?

Daviday · May 13th, 2010, 03:51

These are the Three parts i Put in Tonight.
1 the hammer cocks back and is operational.
2 the gun shoots once on semi or auto
3 the hammer locks on the sear, if i pull the trigger no response
4 i apply a little bit of pressure on the trigger"Forward" and the hammer clicks forward slitghly.
5 i pull the trigger again it shoots and repeats 1-5.

Shirley · May 13th, 2010, 04:04

After a shot in semi, it gets stuck again?

Just to warn you, steel disconnecter, and steel hammer without a steel trigger can cause trouble of wearing out your trigger very fast.

Again, is your SCAR model a clear body version?

Daviday · May 13th, 2010, 04:08

nope it's a tan WE, 3G. I guess its time to get a steal trigger...

Shirley · May 13th, 2010, 04:13

The problem is your bolt is not resseting the sear. Basically the bolt moves back, the hammer gets cocked back, locked under the sear, then the bolt spring forward, hitting into the sear bar releasing the trigger from the sear.

If you're able to shoot your gun in semi continuosly, and shoot a shot in auto, and locks back, you forsure have body fitment issues.

If it's not that, then remove each part and try it out with 1 part at a time to see which the problem is.

Daviday · May 13th, 2010, 04:17

Well, I do have a light weight bolt and when I cock the gun manually, it works fine, same with the hammer check without the upper. I think it might be cycling to fast.

Daviday · May 13th, 2010, 04:23

so should i reset my bolt? and how exactly do i make sure it's properly alined

Shirley · May 13th, 2010, 04:30

Quote:

Originally Posted by Daviday

so should i reset my bolt? and how exactly do i make sure it's properly alined

What do you mean by resetting your bolt?

If there's no wobble in your recievers.

Was your SCAR working before you threw in those aftermarket parts?

If it was, then put it back all stock parts, then one by one, you put in each part, test it out, and then you will find your problem.

Daviday · May 13th, 2010, 05:21

Well, my old hammer wore down, o I decided to replace the internals with tsc so I could put up with the co2. I know what was wrong with the gun before I fixed it and so it was just a matter of fixing the gun. The standard we parts are crap when it comes to using co2 and break quickly. Ive done my research however this was a surprise to me.

shaharov · May 13th, 2010, 17:41

Is there a place where I can order replacement lower recievers for my WE SCAR (mine cracked). I'd perfer to get a full color one but not picky

Shirley · May 13th, 2010, 18:50

Quote:

Originally Posted by shaharov

Is there a place where I can order replacement lower recievers for my WE SCAR (mine cracked). I'd perfer to get a full color one but not picky

Replacements, I haven't seen any places that sell, but you can always place a wanted ad for one, or ask a WE distributor for example Velocity Arms.

shaharov · May 14th, 2010, 04:34

Quote:

Originally Posted by Mr.Hitman

Replacements, I haven't seen any places that sell, but you can always place a wanted ad for one, or ask a WE distributor for example Velocity Arms.

Airsoft buddy is carrying complete list of WE M4 parts.. I think they may be able to get scar parts as well as they custom order everything from WE.

Rugger_can · May 14th, 2010, 05:11

Quote:

Originally Posted by shaharov

Airsoft buddy is carrying complete list of WE M4 parts.. I think they may be able to get scar parts as well as they custom order everything from WE.

They are located in Hong Kong, Thus your receiver runs the risk of being seized.

shaharov · May 14th, 2010, 18:23

Quote:

Originally Posted by Rugger_can

They are located in Hong Kong, Thus your receiver runs the risk of being seized.

I realize that... I'm just putting it out there that if anyone needs parts airsoft buddy has a complete list of all parts for the WE M4 and can get parts (I think all parts) for the WE SCAR

ShelledPants · May 14th, 2010, 18:24

Hey gang,

I just posted up a cleaning guide. Please inform me of any corrections.

http://www.airsoftcanada.com/showthr...50#post1234750

Cheers,

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 13th, 2010, 03:51	#377
Daviday Trader rating Join Date: Aug 2008	These are the Three parts i Put in Tonight. 1 the hammer cocks back and is operational. 2 the gun shoots once on semi or auto 3 the hammer locks on the sear, if i pull the trigger no response 4 i apply a little bit of pressure on the trigger"Forward" and the hammer clicks forward slitghly. 5 i pull the trigger again it shoots and repeats 1-5. __________________ WE SCAR TM M9 TACTICAL

May 13th, 2010, 04:04	#378
Shirley A-56 aka Mr.Hitman Trader rating Join Date: Nov 2007 Location: Toronto, ON	After a shot in semi, it gets stuck again? Just to warn you, steel disconnecter, and steel hammer without a steel trigger can cause trouble of wearing out your trigger very fast. Again, is your SCAR model a clear body version? __________________ CANADIAN AIRSOFT PRACTICAL SHOOTING (CAPS) CAPS DIRECTOR # 0047

May 13th, 2010, 04:08	#379
Daviday Trader rating Join Date: Aug 2008	nope it's a tan WE, 3G. I guess its time to get a steal trigger... __________________ WE SCAR TM M9 TACTICAL

May 13th, 2010, 04:13	#380
Shirley A-56 aka Mr.Hitman Trader rating Join Date: Nov 2007 Location: Toronto, ON	The problem is your bolt is not resseting the sear. Basically the bolt moves back, the hammer gets cocked back, locked under the sear, then the bolt spring forward, hitting into the sear bar releasing the trigger from the sear. If you're able to shoot your gun in semi continuosly, and shoot a shot in auto, and locks back, you forsure have body fitment issues. If it's not that, then remove each part and try it out with 1 part at a time to see which the problem is. __________________ CANADIAN AIRSOFT PRACTICAL SHOOTING (CAPS) CAPS DIRECTOR # 0047

May 13th, 2010, 04:17	#381
Daviday Trader rating Join Date: Aug 2008	Well, I do have a light weight bolt and when I cock the gun manually, it works fine, same with the hammer check without the upper. I think it might be cycling to fast. __________________ WE SCAR TM M9 TACTICAL

May 13th, 2010, 04:23	#382
Daviday Trader rating Join Date: Aug 2008	so should i reset my bolt? and how exactly do i make sure it's properly alined __________________ WE SCAR TM M9 TACTICAL

May 13th, 2010, 05:21	#384
Daviday Trader rating Join Date: Aug 2008	Well, my old hammer wore down, o I decided to replace the internals with tsc so I could put up with the co2. I know what was wrong with the gun before I fixed it and so it was just a matter of fixing the gun. The standard we parts are crap when it comes to using co2 and break quickly. Ive done my research however this was a surprise to me. __________________ WE SCAR TM M9 TACTICAL

May 13th, 2010, 17:41	#385
shaharov Trader rating Join Date: Jul 2009 Location: Duncan, BC (just North of Victoria)	Is there a place where I can order replacement lower recievers for my WE SCAR (mine cracked). I'd perfer to get a full color one but not picky __________________ Friendly Fire...... ISN'T!!

May 14th, 2010, 18:24	#390
ShelledPants Trader rating Join Date: Feb 2008 Location: Toronto, On	Hey gang, I just posted up a cleaning guide. Please inform me of any corrections. http://www.airsoftcanada.com/showthr...50#post1234750 Cheers, __________________ Ár skal r?*sa, sá er annars vill fé eða fjör hafa. Sjaldan liggjandi úlfur lær um getur né sofandi maður sigur.

WETTI/AWSS - M4/SCAR/HK416 - Technical Summary Thread

Upgrades & Modifications