FAQ for Tokyo Marui Hi-Capa, 2011, 1911, MEU & Detonics type variants

[ILLusion]

I couldn't tell what that washer was at first, because the photo of it didn't put a scale to it. It would have told more if it was placed beside the rest of the components in the same photo.

However, I'm 99% certain it's the washer that's supposed to sit between the shock buffer and the recoil spring, as I don't see any washer there at all in the other photos. If you run your gun without a steel washer in that location, the action will actually chop that shock buffer to pieces.

As for the guide rod coming loose, yes, it is an issue. The two holes drilled through the side, are to allow you to insert keys through them, so that you can crank down the rod with enough torque to secure the two parts. Put some Loctite on the threads so that it won't come apart again. For your particular setup, you shouldn't ever have to take the two pieces apart. They're only machined as two pieces, as it's easier to manufacture a base unit as one piece, and then a second piece that screws down to the required length.

[TaroBear]

Ah, okay. So it does go where I thought. At this point, how can I screw the rod together efficiently? The best way I've found is to slip half of the rod and the spring in, then push the other part of the rod in through the business end of the slide.

If it was one piece, I'd just slip everything into the slide from the inside, but it just doesn't seem possible here. It doesn't help that the spring is extremely stiff.

What's the *proper* slide stripping procedure for this setup? Is it exactly the same as the Hi Capa or 1911 set ups, and just requires a bit more finesse? I ask because I don't recall this happening previously.

[ILLusion]

Originally Posted by TaroBear

What's the *proper* slide stripping procedure for this setup? Is it exactly the same as the Hi Capa or 1911 set ups, and just requires a bit more finesse?

^^^ THIS.

That's how I got your gun together when I'd assembled it. Like I said in my previous reply, you shouldn't ever have to disassemble the rod at all. It should all install internally.

With real steel Hi-Capas, there is actually a tool that you can purchase, which is basically a shim that you would jam in between the rod and the bushing while the slide was racked back. That would lock the assembly in a compressed state, making removal and re-insertion much easier.

[mighty_kit]

you don't need a special tool. I have a similar setup.
just push the recoil rod forward, keep the spring for 1 second and push back only the recoil rod. then insert an allen key that fits the hole.

[ILLusion]

Originally Posted by mighty_kit

you don't need a special tool. I have a similar setup.
just push the recoil rod forward, keep the spring for 1 second and push back only the recoil rod. then insert an allen key that fits the hole.

His setup is not the same as yours, Cristian. Yours has the integrated compensator with the longer recoil rod, so for your particular setup, you have no option but to disassemble the recoil rod each time.

tarobear's setup is different, in that it's just a standard government length bull barrel setup with no compensator. Assembly and disassembly is exactly the same as any other similar setup out there, and can be extracted and re-inserted internally with zero disassembly of the rod.

[TaroBear]

Got it back in, thanks. Man, that spring is stiff. I've always been curious, why are aftermarket springs coloured differently? Just cosmetics?

[ILLusion]

Yep, that's pretty much it. Brand identification, or differentiation between the gun platforms they're purposed for.

[mighty_kit]

I understand...I'm glad I found an easy way to dissasemble the recoil rod.

[TaroBear]

http://www.redwolfairsoft.com/redwol..._Stainless.htm

Am I reading this product description right? There are finally ambi mag catchs for the 1911?

[ILLusion]

Originally Posted by TaroBear

http://www.redwolfairsoft.com/redwol..._Stainless.htm

Am I reading this product description right? There are finally ambi mag catchs for the 1911?

These have been available in the real steel world for quite some time. It was just eventual that they would be made available for airsoft.

The mechanism is basically the same thing as ambi mag catches for the Armalite platform. There is a lever mounted under an opposing side button that lifts the mag catch as required.

There are more moving parts, and more moving SMALL parts to do this, so there is a higher chance of failure and/or jamming with such mechanisms... but, it's a decent compromise for lefties who are desperate for a solution.

[Black Jack]

Ive got a socom gear 1911 (punisher custom). Its a great gun, and Ive only upgraded the inner barrel and hopup rubber.

The oonly thing is that occasionally it gets locked up when the hammer catches under the back of the slide as its returning.

Is there a way to fix this from happening?

[ILLusion]

Originally Posted by Col.Angus

Ive got a socom gear 1911 (punisher custom). Its a great gun, and Ive only upgraded the inner barrel and hopup rubber.

The oonly thing is that occasionally it gets locked up when the hammer catches under the back of the slide as its returning.

Is there a way to fix this from happening?

Yep. Buy a Marui. LOL

But in all seriousness, I *think* you should be able to just swap in a Marui based hammer in to the gun, and that should solve your problem. In a number of WE/Socom Gear guns that I've messed with, the hammer hooks were cast too high, on the body, causing it to get in the way of the blowback unit. This would be the best way to solve the problem.

The next best, and even cheaper method, would be to file/machine a steeper and deeper ramp on the inside of the blowback unit, which would allow the slide to ride over the high hammer easier... OR, grind the corner of the hammer down.

[apilar]

Hello guys,

I was looking through this giant post trying to find my answer but i feel pressed for time and its a peculiar situation.

So i bought these two parts a slide and barrel. Order actually yesterday. Today I receive an email saying these parts will not fit together, and if my order was for two separate guns. Very nice of them to ask, but why the hell dont these work together? i am very confussed.

Here are the products that supposedly will not work together.
http://www.dentrinityshop.com/pr_details.jsp?pid=10752

http://www.dentrinityshop.com/pr_details.jsp?pid=9817

If anyone could give tell me why these are not compatible that would be great!

Thanks,
Alex


EDIT:
I think i figured out the problem. The barrel above has a sleeve type things on it that requires the addition of a compensator to keep in place. The image is deceiving.
I will look for a chamber + barrel, and not a one piece.

[ILLusion]

Do you have a compensator to go with the barrel? If not, it will not work. It will just flop around in the slide without a compensator attached to lock it up.

Just tested an ILLusion Kinetics barrel with a Shooters Design slide for the first time. Fit and function is fine.

[Wepeel]

I have a stock TM Hi-Capa 5.1 now and funnily enough I've ran into sort of the opposite of my previous issue with the slide catch not disengaging.

Now on the TM one, if I were to do a quick reload and insert the magazine a little too hard, the slide catch will slip and release the slide, wearing the notch down. I don't even think I insert the magazine that hard.

Is it common on these guns?