|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
May 11th, 2008, 00:12
|
#1 |
|
help opning kings arms ambi mag release
i cant seem to get this dam thing to open as their is no screw to it i dont know how to open it dose any one know how to and ill post pictures of it in a few
__________________
MY COLLECTION AEG M4 coustom full metal with king arms metal body //\\ Galaxy MP5 PDW GAS/SPRING KJW M9 FULLY UPGRADED //\\KWA FULL SIZE USP //\\ TF MAC11 GEAR Coyote Brown CIRAS |
|
|
|
May 11th, 2008, 00:27
|
#2 |
|
Just installed one.
There is a screw on the right side (at the end of the rod) holding the button in place. Also, the one I had needed a little force to be pulled off when the screw was removed. Can't blame them for making a tightfit on that. |
|
|
|
|
May 11th, 2008, 00:50
|
#3 |
|
|
is the hex key smaller then 1.5 mm cuz the one is really frign small
__________________
MY COLLECTION AEG M4 coustom full metal with king arms metal body //\\ Galaxy MP5 PDW GAS/SPRING KJW M9 FULLY UPGRADED //\\KWA FULL SIZE USP //\\ TF MAC11 GEAR Coyote Brown CIRAS |
|
|
|
|
May 11th, 2008, 00:53
|
#4 |
|
Red Wine & Adderall
|
both 1.5mm and 1/16 inch worked for on my kingarms one, it was even a little too lose in my opinion.
__________________
 "Its only a little bit on fire" Last edited by TokyoSeven; May 11th, 2008 at 00:55.. |
|
|
|
|
May 11th, 2008, 02:07
|
#5 |
|
|
still cant find the screw and the front of the catch were the screw would be knormal located it wont take a 1.5mm hex key any outher suggestions
__________________
MY COLLECTION AEG M4 coustom full metal with king arms metal body //\\ Galaxy MP5 PDW GAS/SPRING KJW M9 FULLY UPGRADED //\\KWA FULL SIZE USP //\\ TF MAC11 GEAR Coyote Brown CIRAS |
|
|
|
|
May 11th, 2008, 02:40
|
#6 |
|
kos
|
Are you sure it's a KA unit?
The only units I know that DON'T have a screw, are NORGON AMBI-Catches. Those are for RS, though... |
|
|
|
|
May 11th, 2008, 04:05
|
#7 | |
|
my last 2 KA ambi latches have been 1.3mm
__________________
JAYHAD: Commander - Airsoft Assassins distributing plastic death one nerd at a time JOC Age Verifier Quote:
|
|
|
|
|
|
May 11th, 2008, 13:26
|
#8 |
|
|
1.3mm can be easier to find in 0.05". It is the same size.
|
|
|
|
|
May 11th, 2008, 14:02
|
#9 |
|
|
thanks im hedding off to the local harwear store to pick up both and yes thats kings amrs came off their site and i recived mine in an unopend kings arms pacage
__________________
MY COLLECTION AEG M4 coustom full metal with king arms metal body //\\ Galaxy MP5 PDW GAS/SPRING KJW M9 FULLY UPGRADED //\\KWA FULL SIZE USP //\\ TF MAC11 GEAR Coyote Brown CIRAS |
|
|
|
 |
|
||||||
| Bookmarks |
| Thread Tools | |
|
|
 |
