|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
May 13th, 2014, 19:41
|
#1 |
|
Make Your Own PMags For PTW
Here is a top view of the mags once they are finished.
Top one is clearly NOT for PTW, unless you like 3200 fps.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:17.. |
|
|
|
May 13th, 2014, 19:42
|
#2 |
|
|
For these mags, I used FDE Magpul Gen 2 (now called MOE) as they are cheap and easy to get. Each one cost me $23 plus $5 for the ranger plate.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 19:58.. |
|
|
|
|
May 13th, 2014, 19:45
|
#3 |
|
|
Unfortunately, if you buy these mags in Canada, they will be pinned to correspond to our 5-round mag limit legislation. The rivet needs to be removed and as you are removing the feed lips from the mags, they will no longer be magazines as they can no longer hold nor feed rounds into any firearm.
It also helps if you enlarge the slot for the bolt stop.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 14th, 2014 at 01:06.. |
|
|
|
|
May 13th, 2014, 19:46
|
#4 |
|
|
These are all the tools you will need. A rotary tool, a cut-off disc and a fine grinding bit.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:01.. |
|
|
|
|
May 13th, 2014, 19:48
|
#5 |
|
|
There is a mold seam along the top of the mag at the feed lips. It is right above the calibre symbol and runs the full length of the mag. Cut along the seam, both sides, front to back.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:02.. |
|
|
|
|
May 13th, 2014, 19:49
|
#6 |
|
|
Use the grinding bit to remove the internal material necessary to accomodate the mag fingers and their cover. This is the only internal material to be removed. Chamfer the left side of the mag shell to allow for smooth insertion over the mag catch.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:11.. |
|
|
|
|
May 13th, 2014, 19:50
|
#7 |
|
|
Remove the endplate lock from the mag spring, and grind away the material that grabs the spring.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:04.. |
|
|
|
|
May 13th, 2014, 19:53
|
#8 |
|
|
Grind away just a bit of the rear lug on the mag shell. Basically, about 1/8", just enough to allow easy insertion of the guts into the shell. Not too easy though, a little friction is OK.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:07.. |
|
|
|
|
May 13th, 2014, 19:54
|
#9 |
|
|
Add a little tape or self-adhesive foam or similar to keep the guts sitting centered in the shell.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:07.. |
|
|
|
|
May 13th, 2014, 19:55
|
#10 |
|
|
Use a piece of closed-cell foam to provide tension on the endplate lock. Assemble the endplate of your choice. Your mag is now complete.
Once you do the first one or two, it gets real easy. I did 8 in about an hour. The mags seat fine in most lowers, including the dreaded FCC. No pins, set screws or cutouts for the finger plate.
__________________
Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy. Last edited by mcguyver; May 13th, 2014 at 20:11.. |
|
|
|
|
May 13th, 2014, 20:19
|
#11 |
|
Freaking awesome, thanks McGuyver!
__________________
 |
|
|
|
 |
|
||||||
| Bookmarks |
| Thread Tools | |
|
|
 |
