Airsoft Canada

Go Back   Airsoft Canada > Discussion > Upgrades & Modifications
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

LCT AK-74 NV Flash Hider --- the thread!

:

Upgrades & Modifications

Reply
 
Thread Tools
Old March 20th, 2014, 00:04   #1
Sherbert85
 
Sherbert85's Avatar
 
Join Date: May 2008
Location: Camrose
LCT AK-74 NV Flash Hider --- the thread!

Mission: I want to remove the flash hider from my LCT AK-74 to replace it with a totally awesome new 14mm CCW flash hider.

Problem: HOW THE FRICK DO YOU DO IT?!

Things I already know: The flash hider spins off counter clock wise to reveal the smaller 14mm thread base holding it on.

After two fruitless hours of searching I have come up with the following:

1) Apparently nobody has a the full size NV, just the AK74U, because there's lots on how to do that one. Oh, and I'd like to not break it like the one US guy suggested. Oh, and apparently LCT does things different.

2) I must defer to superior experience.

3) HELP MEEEEEEEEEEEEEEEE! I BEG OF YOU! I JUST WANT TO KNOW HOW TO DO IT OMG! SPOON FEED ME WAHHH WAHHH WAHHH

4) Technical illustrations provided.
Attached Images
File Type: jpg ak1.jpg (72.0 KB, 41 views)
File Type: jpg ak2.jpg (52.6 KB, 36 views)
File Type: jpg ak3.jpg (62.5 KB, 36 views)
Sherbert85 is offline   Reply With Quote
Old March 20th, 2014, 00:14   #2
666
 
666's Avatar
 
Join Date: Jul 2004
Location: Toronto, Ontario
Have you tried pushing "post keeping thing from spinning" back and turning flash hider? It should come off fairly easy. Hex screw is probably what's holding whole front sight block attached to barrel. On every AK I own front sight is being held by that one hex screw.
666 is offline   Reply With Quote
Old March 20th, 2014, 00:31   #3
Ramcke
 
Ramcke's Avatar
 
Join Date: Jan 2009
Location: Markham, ON
Post or pin has a spring pushing it forward. I used a very small flat head screwdriver to push the pin back. Then I turn the flash hider, you may need a bigger screwdriver inserted on the side holes of flash hider to get a better twist if its to tight to turn by hand.

Sent from my SM-G730W8 using Tapatalk
__________________

Don't run! You'll just die tired.


Primary: LCT AKS-74M Back-up: LCT AK 104
Ramcke is offline   Reply With Quote
Old March 20th, 2014, 00:48   #4
Sherbert85
 
Sherbert85's Avatar
 
Join Date: May 2008
Location: Camrose
Thank you, gentlemen. That was the way.

Used, exactly, a very small flat head (from eyeglass repair kit) to press post in. Had to turn flash hider a full turn, then repress post, repeat a couple times until the threading was loose enough to allow it to spin freely. Once this was done, it came off easily, because that single grub screw holding the larger thread base was not installed correctly at factory. So spun it off. Ta-da!

Obviously, that single spring is housed inside the front sight. There is nothing holding it in.
Attached Images
File Type: jpg ak04.jpg (33.2 KB, 33 views)
File Type: jpg ak05.jpg (31.0 KB, 24 views)
Sherbert85 is offline   Reply With Quote
Old March 20th, 2014, 02:50   #5
pusangani
Official ASC "Dumb Ass"
 
pusangani's Avatar
 
Join Date: Jan 2008
Location: Scarbrah, Ontario
this is exactly how it is on my LCT AKMSU, but even with the grub screw removed I can't get it to turn for nothing
__________________
pusangani is offline   Reply With Quote
Old March 20th, 2014, 09:32   #6
Disco_Dante
 
Disco_Dante's Avatar
 
Join Date: Oct 2007
Location: GTA
Bring it by sometime Sunil and I'll use my man-hands
__________________


Not for glory, nor riches, nor honours, but for freedom alone, which no good man gives up except with his life.
Disco_Dante is offline   Reply With Quote
Old March 20th, 2014, 09:59   #7
Stealth
Mr. Silencer
 
Join Date: Dec 2001
Location: Toronto
PM dongtheimpaler - he is looking for the flash-hider you just removed.
Stealth is offline   Reply With Quote
Old March 20th, 2014, 11:15   #8
dongtheimpaler
Banned
 
dongtheimpaler's Avatar
 
Join Date: Nov 2012
Location: Vancouver, BC
Yes I am, thanks.
dongtheimpaler is offline   Reply With Quote
Old March 20th, 2014, 13:42   #9
pusangani
Official ASC "Dumb Ass"
 
pusangani's Avatar
 
Join Date: Jan 2008
Location: Scarbrah, Ontario
Quote:
Originally Posted by Disco_Dante View Post
Bring it by sometime Sunil and I'll use my man-hands
thanks, I've got a jar of peanut butter I'll bring too
__________________
pusangani is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Upgrades & Modifications

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada

All times are GMT -4. The time now is 05:09.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.