|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
August 31st, 2010, 23:09 | #1 |
G&G M4 Problem
Hi everyone,
I have a G&G M4 that is not working a buddy of mine took it apart and found a broken gear in my gearbox. i got new gears and put it back together and it still doesn't work. it seems to me that its an electrical problem because the battery was charged and nothing hapened so if anyone knows whats the problem or if they can help please contact me. Thanks |
|
September 1st, 2010, 01:40 | #2 |
You're being pretty vague. No one will be able to help you unless you give more details.
Also, this should have been posted in the Gun Doctor section. |
|
September 1st, 2010, 10:22 | #3 |
Did you check your fuse, if you have one that is.
|
|
September 1st, 2010, 17:10 | #4 |
If you disassembled the gun, check to make sure you re-connected the wires to the motor.
|
|
September 1st, 2010, 17:14 | #5 |
what battery are you using and what charger? The battery you got with it? Did you try another battery? Trouble shoot the wiring.. If not the battery might be bad. I had to buy a new battery to replace the one i got with my G&G cause it was a bad battery and doesn't hold a charge
__________________
-Dangerous- BA Level 3 Certified |
|
September 1st, 2010, 18:43 | #6 |
uMadd, Padd?
|
Check your gearbox wires, it's possible that they were damaged if your friend reassembled the upper receiver.
|
September 1st, 2010, 18:55 | #7 |
a.k.a. Phoneguy
|
Going on what Augie says, when you re-connected, or your friend reconnected, the wires to the motor you have to be careful not to bend the connector back and forth too much while you're trying to push it onto the spade of the motor. Doing this will break the connection and it won't be visible under the heat shrink of the connector you are pushing on. I'm not saying that this is for sure the problem, I'm just relating a problem I had with mine that might have happened to yours.
|
September 1st, 2010, 19:43 | #8 |
wow another G&G with a broken gear. They must make those things out of corn.
Is your fuse blown? I you may have blown it by trying to fire with the broken gear. This would put load on the motor/battery and heat the fuse up to a breaking point. Also make sure your motor hight is not jammed right in that could be stopping ti as well. But that would usually cause a *tick* sound when the trigger is pulled. I tell you what though, G&G has cured me of ever buying a clone gun. |
|
September 5th, 2010, 21:56 | #9 |
a.k.a. Phoneguy
|
So what's the update JAKE. Were you able to find out why the motor wasn't spinning up.
Do what Dart says and pop the motor plate off to make sure that the motor height is not jamming the gears. Also, while you got it dropped and the wires still hooked up, see if the motor spins up, before you pop it back into the handle. If not, check the fuse if it has one. You might also want to check the trigger switch in the gearbox as well if the fuse checks out and the connectors on the motor check out. |
September 6th, 2010, 16:50 | #10 |
are you using the stock nunchuck G&G batteries? becase if so throw those POS out. they dont hold charge what so ever
|
|
September 6th, 2010, 17:21 | #11 |
Yeah the one i got with my G&G was dirt and didn;t hold a charge at all. But i recently bought a king arms and thats a lot better. I bought a B6D charger too... I got my G&G battery back in working order though but the KA is better with a higher mAh
__________________
-Dangerous- BA Level 3 Certified |
|
|
Bookmarks |
Thread Tools | |
|
|