Airsoft Canada
http://triggerairsoft.com/shop/

Go Back   Airsoft Canada > Information Center > Newbie Tank
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Clearsoft DIY reinforcement

:

Newbie Tank

Reply
 
Thread Tools
Old August 7th, 2009, 05:37   #1
Con Murder
 
Con Murder's Avatar
 
Join Date: May 2009
Location: Lethbridge Alberta Canada
Clearsoft DIY reinforcement

This should fit in here as many of you own guns that have clear recievers and such. You may start to notice weakpoints on the body as you begin to take apart and upgrade it.
I was just thinking about the stress I put on some of my clear plastic bodies while working on them (JG and Cybergun/Swissarms respectively). And decided that some key points (ie all the screw holes) could be reinforced by say a washer. But then I remembered that plastic to metal glues are kinda imperfect, so I scrapped the thoughts until it hit me! By making small 'washers' from other plastics you could glue the peice into the rear side of the hole, provided you file some of it back. I used the kind of plastic that I have lots of. Like old student cards or used gift cards, guitar pics work best for me.

You will need:
Hobby Knife
File
Punch/Drill/Dremmel
Good glue that bonds the plastics


First step.

Ensure that the plastic you choose is pliable and clean, able to suply enough to finish the job. The screw hole will require a small amount but give it 1 square inch each.

Second step.

Gently file/dremmel the rear side of any screwhole that apears affected by strain the depth that would equal your chosen plastic. At this point it is imperative that you understand the whole entirety of the weapon, what is tight fitting and how deep this particular screw is going.

Third step.

Cut out a peice of the plastic in the shape you need, overestimate and sand into perfection.

Fourth step.

Dremmel/Drill a hole nearly the same size as the screw in the apropriate place of your plastic peice.

Fifth step.

Glue the plastic into the space you created for it. Do not use excess glue as this will make a mess and ruin the looks of the weapon.

And now you have your reinforced screwholes!

The use of a malleable plastic is to help the glue bond and the stress to be less effictive on the plastic reciever.
__________________
Con Murder
Dark Rhino
L.A. Airsoft
Con Murder is offline   Reply With Quote
Old August 7th, 2009, 11:19   #2
AngelusNex
formerly Sepulcrum
 
AngelusNex's Avatar
 
Join Date: May 2007
Location: Kingston,ON, aka Funkasia
Send a message via MSN to AngelusNex
Guns with screws going into plastic holes tend to be really cheap and it is always better to either; (if it's a decent aeg, G&G, JG,etc..) get a metal/solid black abs body for it or buy a good gun. I have a G&G cansoft and frankly when the clear lower reciever starts falling apart on me, I'm buying a metal one to replace it.
AngelusNex is offline   Reply With Quote
Old August 7th, 2009, 12:24   #3
IceTray
Majestic Mornings rocking it like a Queen
 
IceTray's Avatar
 
Join Date: Jul 2007
Location: Windsor, ON
Wouldn't it just be easier to buy a gun from the classifieds that isn't made of dirt cheap materials? Or buy a replacement metal body.
__________________
For anyone looking for age verification in the Windsor region: Unfortunately, I will only be verifying people at games, I am currently unable to run around and setup meetings.
IceTray is offline   Reply With Quote
Old August 7th, 2009, 14:27   #4
Con Murder
 
Con Murder's Avatar
 
Join Date: May 2009
Location: Lethbridge Alberta Canada
For the Sig 552 I used this on the front body pin, the first four screws under the hand gaurd and inside the magwell where it screws into the hop up. These are high stress areas that will break before the mechbox, this is simple for me and gives me time to save for the metal body (its expensive in alberta for a recession hobbiest) that might help others.


Quote:
Originally Posted by Sepulcrum View Post
Guns with screws going into plastic holes tend to be really cheap and it is always better to either; (if it's a decent aeg, G&G, JG,etc..) get a metal/solid black abs body for it or buy a good gun. I have a G&G cansoft and frankly when the clear lower reciever starts falling apart on me, I'm buying a metal one to replace it.
You can't always get what you want, but if you try sometimes you might find
you get what you need.
__________________
Con Murder
Dark Rhino
L.A. Airsoft
Con Murder is offline   Reply With Quote
Old August 7th, 2009, 14:30   #5
Con Murder
 
Con Murder's Avatar
 
Join Date: May 2009
Location: Lethbridge Alberta Canada
Quote:
Originally Posted by IceTray View Post
Wouldn't it just be easier to buy a gun from the classifieds that isn't made of dirt cheap materials? Or buy a replacement metal body.
It would if my schedule matched with the local group that knows the verifier, and that is why I wait. One day I will meet this 'nachopudding' the speak of. But until then I got this done and shared it in the newbie tank. Just be happy man, I could have thrown it in the upgrades forum!
__________________
Con Murder
Dark Rhino
L.A. Airsoft
Con Murder is offline   Reply With Quote
Old August 7th, 2009, 16:07   #6
jordan7831
will always be Mike Litoris in our hearts
 
jordan7831's Avatar
 
Join Date: Jul 2004
Location: North York - Toronto
I think its a decent idea for those of us who cant find/afford a metal body. I have a GnG and i had to shell out through the ass for a metal lower, the clearsoft body on it is so frail. Good tip thanks!
jordan7831 is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Information Center > Newbie Tank

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
http://triggerairsoft.com/shop/

All times are GMT -4. The time now is 23:46.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.